Weighing System Surge protector
User Manual
SP151
©ꢀExcellꢀPrecisionꢀLimitedꢀ2012.ꢀ ꢀ AllꢀrightsꢀreservedꢀWorldwide.ꢀ
TheꢀinformationꢀcontainedꢀhereinꢀisꢀtheꢀpropertyꢀofꢀExcellꢀPrecisionꢀLimitedꢀ
andꢀisꢀsuppliedꢀwithoutꢀliabilityꢀforꢀerrorsꢀorꢀomissions.ꢀ ꢀ Noꢀpartꢀmayꢀbeꢀ
reproducedꢀ orꢀ usedꢀ exceptꢀ asꢀ authorisedꢀ byꢀ contractꢀ orꢀ otherꢀ writtenꢀ
permission.ꢀ ꢀ Theꢀ copyrightꢀ andꢀ theꢀ foregoingꢀ restrictionꢀ onꢀ reproductionꢀ
andꢀuseꢀextendꢀtoꢀallꢀmediaꢀinꢀwhichꢀtheꢀinformationꢀmayꢀbeꢀembodied.ꢀ
EXCELL PRECISION CO., LTD
SP151 Weighing System Surge Protector
ꢀ
Theꢀhighꢀperformanceꢀsurgeꢀprotectorꢀdeviceꢀappliesꢀtoꢀ4ꢁꢀorꢀ6ꢁwireꢀloadꢀcellꢀ
weighingꢀsystemsꢀorꢀotherꢀrelatedꢀapplications.ꢀ
ꢀ
1. General
SP151ꢀSurgeꢀProtectorꢀisꢀdesignedꢀforꢀaccessingꢀdirectꢀintoꢀtheꢀcablingꢀofꢀtheꢀweighingꢀ
system,ꢀinꢀorderꢀtoꢀpreventꢀtheꢀloadꢀcellsꢀandꢀotherꢀsensitiveꢀelectronicꢀcomponentsꢀfromꢀ
damageꢀbyꢀaꢀnearꢀsurgeꢀstrikeꢀorꢀpowerꢀfailure.ꢀSurgeꢀprotectorꢀworksꢀatꢀtheꢀlocalꢀonly,ꢀ
therefore,ꢀSP151ꢀdevicesꢀshouldꢀbeꢀinstalledꢀonꢀbothꢀendsꢀofꢀcircuitryꢀloop.ꢀ
ꢀ
Aꢀcompleteꢀsystemꢀprotectionꢀrequiresꢀadditionalꢀsurgeꢀprotectionꢀdevice(s)ꢀtoꢀensureꢀ
thatꢀotherꢀitems,ꢀsuchꢀasꢀACꢀpower,ꢀexternalꢀprinters,ꢀmainframes,ꢀandꢀtelephoneꢀandꢀsoꢀ
on.ꢀ
ꢀ
2. Installation
Theꢀfollowingꢀrecommendationꢀisꢀonlyꢀasꢀaꢀreference.ꢀTakeꢀintoꢀaccountꢀofꢀlocalꢀconditions,ꢀ
theꢀinstallationꢀshouldꢀalwaysꢀbeꢀcarriedꢀoutꢀbyꢀprofessionals.ꢀ
ꢀ
2.1 Siting
SP151ꢀshouldꢀbeꢀsetꢀwithinꢀ3mꢀfromꢀtheꢀloadꢀcellsꢀorꢀsystemsꢀtoꢀbeꢀprotected.ꢀForꢀtheꢀ
maximumꢀdegreeꢀofꢀprotection,ꢀSP151ꢀshouldꢀbeꢀusedꢀatꢀbothꢀendsꢀconcurrentlyꢀofꢀtheꢀ
interconnectedꢀcables.ꢀInꢀgeneral,ꢀinstallꢀaꢀprotectiveꢀdeviceꢀbetweenꢀtheꢀjunctionꢀboxꢀandꢀ
loadꢀcellsꢀsetꢀ(Figureꢀ1).ꢀSomeꢀsystemsꢀspecifyꢀloadꢀcellꢀindividualꢀcable(s),ꢀprotectionsꢀareꢀ
neededꢀforꢀeveryꢀloadꢀcellꢀ(Figureꢀ2).ꢀWithinꢀtheꢀweighbridge,ꢀtheꢀSP151ꢀshouldꢀbeꢀsetꢀ
closeꢀtoꢀtheꢀindicationꢀsystems,ꢀtheꢀinterconnectingꢀcablesꢀmustꢀbeꢀseparatedꢀbyꢀatꢀ
leastꢀ50mmꢀfromꢀotherꢀirrelevantꢀcables.ꢀ
ꢀ
1ꢀ
ZSME000000016ꢀ
EXCELL PRECISION CO., LTD
ꢀ
ꢀ
Loadꢀ ꢀ
Cellꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Loadꢀ ꢀ
Cellꢀ
Juctionꢀ
Boxꢀ
Loadꢀ ꢀ
Cellꢀ
Loadꢀ ꢀ
Cellꢀ
SP151ꢀ
Connectionꢀtoꢀweightꢀcabinꢀ
LocalꢀStructuralꢀearthꢀbondꢀ
Figureꢀ1ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Loadꢀ ꢀ
Cellꢀ
Loadꢀ ꢀ
SP151ꢀ
Cellꢀ
SP151ꢀ
Loadꢀ ꢀ
SP151ꢀ
Cellꢀ
Loadꢀ ꢀ
Cellꢀ
SP151ꢀ
Figureꢀ2ꢀ
ꢀ
ꢀ
ꢀ
2ꢀ
ZSME000000016ꢀ
EXCELL PRECISION CO., LTD
2.2 Securing
ꢀ
◄ꢀ ꢀ SP151ꢀshouldꢀbeꢀmountedꢀvertically,ꢀandꢀ
theꢀcableꢀshouldꢀbeꢀconnectedꢀupsideꢀ
downꢀtoꢀavoidꢀwaterꢀfromꢀseepage.ꢀ
ꢀ
ꢀ
3ꢀ
ZSME000000016ꢀ
EXCELL PRECISION CO., LTD
ꢀ
▼ꢀSP151ꢀsealingꢀringꢀhasꢀ4ꢀmountingꢀholesꢀwithꢀcenterꢀtoꢀcenterꢀspacingꢀofꢀ ꢀ
113.5ꢀ×ꢀ113.5ꢀmm.ꢀꢀ
UsingꢀM4x16ꢀorꢀM4x20ꢀroundꢀheadꢀscrewꢀtoꢀsecureꢀtheꢀSurgeꢀProtectorꢀboxꢀontoꢀtheꢀ
mountingꢀsurface.ꢀ
ꢀ
ꢀ
ꢀ
UsingꢀM4x16ꢀorꢀM4x20ꢀroundꢀheadꢀ
screwꢀtoꢀsecureꢀtheꢀSurgeꢀProtectorꢀ
boxꢀontoꢀtheꢀmountingꢀsurface.ꢀ
ꢀ
4ꢀ
ZSME000000016ꢀ
EXCELL PRECISION CO., LTD
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Lockꢀattachedꢀtoꢀtheꢀscrewꢀsizeꢀ
ꢀ
ꢀ
Theꢀscrewꢀdiameterꢀisꢀ4mm,ꢀandꢀ7mmꢀforꢀtheꢀheadꢀdiameterꢀ(M4ꢀscrewsꢀminimumꢀlengthꢀ
isꢀ16mm).ꢀTheꢀstainlessꢀsteelꢀscrewsꢀareꢀrecommendedꢀtoꢀuseꢀforꢀsecuringꢀpurpose.ꢀꢀꢀ
Cablesꢀwithinꢀ200mmꢀfromꢀSP151ꢀshouldꢀbeꢀsupportedꢀandꢀfixedꢀtoꢀpreventꢀtheꢀcableꢀ
connectorꢀfromꢀunableꢀtoꢀsupportꢀtheꢀweightꢀofꢀtheꢀcable.ꢀ
ꢀ
5ꢀ
ZSME000000016ꢀ
EXCELL PRECISION CO., LTD
2.3 Grounding
Properlyꢀgroundingꢀcanꢀonlyꢀelaborateꢀtheꢀperformanceꢀofꢀaꢀsurgeꢀprotector.ꢀToꢀselectꢀtheꢀ
weldingꢀpointꢀbyꢀreferringꢀtoꢀtheꢀlocalꢀvoltage,ꢀallꢀtheꢀweldingꢀpointsꢀwillꢀshareꢀtheꢀꢀ
commonꢁmodeꢀvoltageꢀtoꢀtheꢀground.ꢀTheꢀweldingꢀpointꢀisꢀconnectedꢀtoꢀtheꢀlocalꢀgroundꢀ
networkꢀorꢀgroundꢀrodꢀsystem;ꢀhence,ꢀnoꢀextraꢀgroundꢀnetworkꢀorꢀgroundꢀrodꢀsystemꢀisꢀ
neededꢀtoꢀbeꢀinstalled.ꢀ
ꢀ
Properꢀgroundingꢀisꢀtheꢀlocalꢀstructureꢀofꢀtheꢀdeviceꢀ(Figureꢀ1ꢀandꢀFigureꢀ2),ꢀnoꢀmatterꢀ
connectedꢀtoꢀtheꢀsteelꢀconnectionꢀofꢀmetalꢀorꢀreinforcedꢀconcreteꢀweighbridge.ꢀFromꢀtheꢀꢀ
groundingꢀboltꢀM8ꢀexternalꢀconnectꢀtoꢀtheꢀgroundꢀwireꢀofꢀtheꢀgroundingꢀpointꢀ(10mm2mmꢀ
copperꢀorꢀequivalentꢀmetalꢀwireꢀorꢀribbon).ꢀTheꢀcombinationꢀthatꢀlessꢀthanꢀ3mꢀdevelopsꢀforꢀ
optimumꢀperformance.ꢀUseꢀproperꢀamountꢀofꢀpreservativesꢀtoꢀprotectꢀtheꢀexposedꢀmetal.ꢀ
ꢀ
Inꢀloadometerꢀ(weighbridge)ꢀorꢀcontrolꢀroom,ꢀSP151ꢀsurgeꢀprotectorꢀshouldꢀbeꢀlocatedꢀ
closeꢀtoꢀtheꢀweighingꢀcomputerꢀorꢀdashboardꢀdisplay,ꢀandꢀtheꢀgroundꢀwireꢀshouldꢀbeꢀ
connectedꢀtoꢀindependentꢀgroundingꢀrodsꢀofꢀtheꢀACꢀpower.ꢀGroundꢀwiresꢀthatꢀmoreꢀthanꢀ
3mꢀlong,ꢀaꢀgroundꢀbetweenꢀtheꢀSP151ꢀwithꢀtheꢀinstrumentꢀisꢀneededꢀ(SeeꢀFigureꢀ4).ꢀ
ꢀ
ꢀ
GroundingꢀWireꢀ
※ꢀTightenꢀtheꢀstudꢀM8ꢀupward
Earthing/groundingꢀ ꢀ
M8
studꢀM8ꢀ
ꢀ
6ꢀ
ZSME000000016ꢀ
EXCELL PRECISION CO., LTD
2.4 Connections
Twoꢀterminalsꢀareꢀprovided,ꢀlabeledꢀ"Fieldꢀcable”ꢀandꢀ“Instrumentꢀcable”.ꢀFieldꢀcableꢀisꢀtheꢀ
independent,ꢀexposedꢀcableꢀbetweenꢀtheꢀweighbridgeꢀandꢀweighingꢀcabin.ꢀInstrumentꢀorꢀ
loadꢀcellꢀcableꢀisꢀaꢀlocallyꢀshortꢀconnection,ꢀsuchꢀasꢀfromꢀSP151ꢀtoꢀtheꢀjunctionꢀbox,ꢀ
independentꢀloadꢀcellꢀorꢀweighingꢀscale.ꢀEquipmentsꢀconnectedꢀtoꢀtheꢀterminalꢀareꢀsubjectꢀ
toꢀSP151ꢀprotection.ꢀ
ꢀ
SP151ꢀallowsꢀtheꢀ4ꢁwireꢀ(SIG1,ꢀSIG2,ꢀEXC1,ꢀEXC2)ꢀorꢀlineꢀ6ꢀ(SIG1,ꢀSIG2,EXC1,ꢀEXC2,ꢀꢀ
SENSE1,ꢀSENSE2)ꢀasꢀwellꢀasꢀtwoꢀisolatedꢀlines.ꢀTheꢀfunctionꢀofꢀeachꢀterminalꢀisꢀclearlyꢀ
markedꢀonꢀtheꢀjunctionꢀbox.ꢀ ꢀ
ꢀ
Theꢀisolatedꢀlinesꢀconnectedꢀtoꢀfieldꢀcablesꢀandꢀinstrumentationꢀcablesꢀareꢀnotꢀconnectedꢀ
withꢀtheꢀgroundꢀwireꢀofꢀtheꢀSP151ꢀwithoutꢀaffectingꢀtheꢀgroundꢀoperationꢀofꢀtheꢀgeneralꢀ
weighingꢀsystem.ꢀ
Ifꢀyourꢀvendorꢀrequiresꢀtheꢀisolatedꢀlinesꢀtoꢀbeꢀgrounded,ꢀitꢀshouldꢀbeꢀconnectedꢀtoꢀ
theꢀjunctionꢀboxꢀorꢀloadꢀcell.ꢀ ꢀ
ꢀ
Cableꢀthroughꢀtheꢀcableꢀsealꢀsleeve,ꢀstrippedꢀandꢀattachedꢀtoꢀtheꢀcorrespondingꢀꢀ
connectionsꢀareꢀclearlyꢀmarkedꢀandꢀtheꢀsubsequentꢀfailureꢀdetectionꢀwouldꢀbeꢀeasier.ꢀ
Ensureꢀthatꢀtheꢀsealꢀsleeveꢀcasingꢀisꢀtight,ꢀandꢀthenꢀlockꢀtheꢀlid.ꢀ
ꢀ
ꢀ
ꢀ
FieldꢀCableꢀ
ACꢀ Powerꢀ feedꢀ
(Unprotected)ꢀ
SP151ꢀ
Earth/Groundꢀ
Connectionꢀ
Instrumentationꢀ
orꢀCellꢀCableꢀ
*
Subsidiaryꢀearthꢀ
bondꢀifꢀ ꢀ
earth/groundꢀlinkꢀ
>3m/10ft
ꢀ
ConsumerꢀUnitꢀ
WeighꢀComputerꢀ
Figureꢀ4ꢀ
ꢀ
7ꢀ
ZSME000000016ꢀ
EXCELL PRECISION CO., LTD
3. Maintenance
Note:ꢀForꢀcertifiedꢀsystems,ꢀyouꢀmustꢀconfirmꢀthatꢀtheꢀsystemꢀcanꢀbeꢀ
reꢁcalibrated.ꢀBeforeꢀtearingꢀoffꢀtheꢀsealꢀforꢀmaintenance,ꢀaꢀnewꢀcalibrationꢀsealꢀisꢀrequiredꢀ
forꢀreplacingꢀafterꢀtheꢀmaintenance.ꢀ
Processingꢀtheꢀmaintenanceꢀeveryꢀtheꢀotherꢀyear.ꢀ(higherꢀrepairꢀandꢀmaintenanceꢀꢀ
frequencyꢀforꢀparticularlyꢀharshꢀenvironments)ꢀ
3.1ꢀꢀCheckꢀSP151ꢀtoꢀseeꢀifꢀitꢀisꢀsurroundedꢀbyꢀintactꢀandꢀsealedꢀcorrectly.ꢀ
3.2ꢀꢀRemoveꢀtheꢀchassisꢀcoverꢀandꢀconfirmꢀthatꢀtheꢀsealingꢀeffect,ꢀifꢀnecessary,ꢀtoꢀreplaceꢀ
theꢀdamagedꢀsealꢀstrip.ꢀ ꢀ
3.3ꢀꢀCheckꢀallꢀinternalꢀcablesꢀlabeled.ꢀ
3.4ꢀ Checkꢀtheꢀtightnessꢀofꢀallꢀconnectedꢀcables,ꢀandꢀrepairꢀanyꢀlooseꢀorꢀdamagedꢀ
connections.ꢀ
3.5ꢀ Checkꢀtheꢀinternalꢀandꢀexternalꢀgroundingꢀline,ꢀtightenꢀitꢀifꢀloose.ꢀ
ꢀ
4. Troubleshooting
Whenꢀtheꢀelectronicꢀcircuitꢀsystemꢀsufferedꢀfromꢀsurgeꢀstruck,ꢀitꢀwillꢀoperateꢀautomaticallyꢀ
andꢀselfꢁrecovery.ꢀTheꢀSP151ꢀserviceꢀlifespanꢀcouldꢀbeꢀaroundꢀ20ꢀyears,ꢀdependsꢀonꢀtheꢀ
lifespanꢀofꢀtheꢀprotectionꢀcomponentsꢀofꢀtheꢀprimaryꢀgasꢀdischargeꢀtube.ꢀ
ꢀ
ꢀ
ꢀ
Attentionꢀ
FieldꢀcableꢀthatꢀconnectedꢀtoꢀtwoꢀSP151ꢀofꢀtheꢀinstrumentation,ꢀtheꢀisolatedꢀlinesꢀmustꢀbeꢀ
connectedꢀandꢀwithꢀaꢀdrainꢀofꢀpipeline.ꢀ
Whenꢀtheꢀisolatedꢀlinesꢀsufferedꢀfromꢀtheꢀsurge,ꢀtheꢀgasꢀdischargeꢀtubeꢀwillꢀdischargeꢀtoꢀ
theꢀearthꢀtoꢀimproveꢀtheꢀoverallꢀprotection.ꢀ
ꢀ
ꢀ
8ꢀ
ZSME000000016ꢀ
|
CompuSTAR Remote Starter CM4200DX User Manual
Continental Platinum Blender CP42149 User Manual
Cuisinart Blender SMO 56C User Manual
Cypress Computer Hardware AN20639 User Manual
Cypress Computer Hardware CY8C24094 User Manual
Desa Tech Gas Heater CBN20 User Manual
Earthquake Sound Speaker SUB100 User Manual
Fellowes Paper Shredder DS 12Cs User Manual
Field Controls Oxygen Equipment FC95HRV User Manual
Fisher Price Automobile Parts T7160 User Manual