Blower, DVS Gas
(Berkshire, Tree of Life, Prairie, Cedar, 2001 Allegiance)
Part # 99000153
CHECK CONDITION OF SHIPMENT
Upon receipt of this kit, check the condition of the packaging. Damage to the package should be noted on the carrier's freight
receipt. Any damage claims as a result of shipping must be handled through the shipper. Travis Industries will provide assistance
in resolving shipping claims or replacing items not included in the package. Please report any missing items immediately.
COMPATIBILITY
• Lopi Berkshire
• Tree of Life
• Avalon Prairie
• Avalon Cedar
• Lopi Allegiance (2001 model)
ITEMS NEEDED FOR ASSEMBLY
• 11/32” Socket Wrench
• 1/4” Nutdriver
• 1/2” Open End Wrench
PACKING LIST
• Blower Assembly
• Wiring Harness
• Stud Plate
• Thermodisk
• Two Rubber Grommets (with spacers)
• Rheostat Knob
• Two Nuts and Washers
• Rheostat (with attachment nut & lock washer)
INSTALLATION INSTRUCTIONS
WARNING:
Turn the gas control valve to off and make sure the appliance has fully cooled prior to
conducting service.
1
Attach the two black wires on the included wiring harness to the thermodisk (orientation does not matter). Then slide
the thermodisk into the holder underneath the burner pan at the right rear of the stove.
All Models
Except the
Tree of Life and
2007 Berkshire
Snap Disk Bracket
(attached to stove)
Back of
Stove
Snap Disk
Snap Disk Wires on Wiring Harness
(Black - orientation does not matter)
Attach the snap disk
Remove the snap disk cover plate below
the burner on the left side (when facing
the stove from the front).
a
b
using the screws
removed in step "a".
Tree of Life
and
Back of Stove
2007 Berkshire
Attach the wires
Snap Disk Wires
c
labeled snap disk to
the snap disk.
(Black - orientation
does not matter)
Page 1 of 4
4070219
Blower, DVS Gas
(Berkshire, Tree of Life, Prairie, Cedar, 2001 Allegiance)
Part # 99000153
3
Slide the left side of the blower mounting bracket over the grommets on the left mounting bracket attached to the
stove (see the illustration below). Then insert the stud plate through the right side grommets and through the right
mounting bracket on the stove. Secure the stud plate with the included washers and nuts
Make sure the bracket
Left Mounting
slides into the groove on
Bracket (on stove)
the rubber grommets.
Rubber
Grommet
Right Mounting
Blower Mounting
Bracket
Bracket (on stove)
Stud Plate
Blower Mounting Bracket
Stud Plate
Blower Mounting Bracket
11/32”
Socket
Washer
Nut
4
Make sure all of the wiring is placed away from the blower impeller and the bottom of the burner. Use lock ties, if
necessary, to ensure no wires are damaged.
Page 3 of 4
4070219
Blower, DVS Gas
(Berkshire, Tree of Life, Prairie, Cedar, 2001 Allegiance)
Part # 99000153
5
Open the control cover following the directions below. Remove the button plug and install the rheostat.
Loosen the two screws holding the control
box in place. This allows access to the
back of the control box.
Attach the rheostat wires to the two
quick connects inside the control
box (orientation does not matter).
NOTE: make sure the
fiberglass heat shield is in
place when re-attaching the
control box (all models except
the cedar).
b
a
Control Box
Phillips
Screwdriver
Rheostat
c
Attach the rheostat to
the control panel with
the included nut and
star washer.
1/2"
Wrench
Back of
Stove
Attach
the knob.
NOTE: this tab fits into the
hole on the mounting bracket.
6
If using the modulating remote thermostat, attach the red and brown wires to the gas control valve.
Attach the red and
brown wires to the top
and bottom terminals
on the gas control
7
Plug the blower in. Let the heater achieve operating temperature and test blower operation.
Page 4 of 4
4070219
|